UCE-CT220L Fault Locator & Curve Tracer

(4 customer reviews)

$299.00

Out of stock

Already 1 persons shown interest.

Buy more, Save more ...

Description

V-I test method is widely used in the World for PCB repairing. Fault detection can be done without energizing PCB boards.

32 different test conditions can be created with different combinations of test voltage, source resistance and frequency values.

The fact that the product has two channels allows simultaneous comparison of two different cards.

Specifications:

  • Display: 4.3 inch 480 × 272 pixel color LCD with Touch screen
  • Channels Number: 2 (A and B)
  • Waveform: Sine wave
  • Test Frequencies: 10Hz, 100Hz, 500Hz, 2000Hz
  • Open circuit Voltage:  ±5V, ±10V, ±20V
  • Source Resistance: 1kΩ, 10kΩ
  • Storage: internal 8MB USB disk for storing waveform image and firmware upgrade (bootload)
  • Power Consumption: 5W
  • Dimensions: 169 x 83 x 31 mm
  • Weight: 295gr

Package List:

  • 1 pc UCE-CT220L Tracer
  • 2 pcs BNC to 4mm banana cable
  • 2 sets multimeter pen (red and black), and with needle high-voltage cap
  • 2 pcs Crocodile Clips
  • 1 pc touch pen
  • 1 pc USB cable

 

 

Additional information

Weight 850 g
Dimensions 23 × 12 × 9 cm

Manual_EN

Manual_TR

How to update firmware of UCE-CT220L


Firmware History

UCE-CT220L V1.09

Released on 2020-01-13

Recent changes;

  • Added resistor and capacitor detection algorithm for both Channels.
  • Some optimizations.

Note: Device must be restarted after firmware upgrade.


UCE-CT220L V1.08 beta

Released on 2019-12-24

Recent changes;

  • New feature: Added resistor and capacitor detection algorithm. And improved calculation algorithm of their values . This feature is only Single Mode (at CH-A) for now.
  • Fixed some bugs.
  • Some optimizations.

UCE-CT220L V1.07

Released on 2019-11-28

Recent changes;

  • Optimized Probe Calibration algorithm (Probe Calibration allows probes with different impedance values ​​to be used in the instrument).
  • Some optimizations.

Note: In order to make probe calibration, device must be restarted after firmware upgrade.


UCE-CT220L V1.05

Released on 2019-09-09

Recent changes;

  • Optimized the angle of Short-Circuit & Open-Circuit curves.
  • Some optimizations.

UCE-CT220L V1.04

Released on 2019-04-17

Recent changes;

  • Fixed a bug in HOLD-RUN Mode

UCE-CT220L V1.03

Released on 2019-02-24

Recent changes;

  • Fixed angle of Short-Circuit curve.
  • Some optimizations.

UCE-CT220L V1.02

Released on 2019-02-16

Recent changes;

  • Added Input voltage error detection algorithm.
  • Reduced the Noise on signals with software optimization.
  • Fixed the time gaps in voltage transitions in scan mode.
  • Some optimizations.

UCE-CT220L V1.01

Released on 2019-01-20

Recent changes;

  • Fixed a bug in Scan Mode.

4 reviews for UCE-CT220L Fault Locator & Curve Tracer

  1. Marco (verified owner)

    I was looking for an affortable, compact and stand-alone V-I Curve Tracer. Something you don’t have to connect to a scope to view V-I curves. I happened to see uCore UCE-CT220L and I soon realized it was what I was looking for. Compact, with a Display and with an affordable price. I ordered it and I have to say I’m happy with it. I use it to troubleshoot electronic boards by comparision and it works as expected. It lacks pulse generator but I knew it from the beginning and I don’t really use it anyway (I had a VI tracer with pulse generator at office before). This VI tracer has two channels (useful to compare boards), a function to save images of the VI curves, connects to PCs with USB ports, easy to update when uCore releases updates (that just happened, this show that product is supported). By now I’m satisfied with it. Adding a Very Low Range would make it perfect to detect very low differences in very low power logic boards where very small differences in data/address bus between board (difficult to detect) are signs of something wrond with the signal. Hope it will be added in near future. I’m not in any way affiliated to uCore alectronics. I just appreciated very much its work and wanted to let others (and uCore itself) know it. There’s some good work going on here!

  2. Ramazan

    Uce kullanıyorum yaklaşık olarak 5 aydır . çok memnunum. son güncelleme iyi olmuş fakat parazit çok .başarılarınızın devamı diliyorum .

  3. ugur

    yaklaşık 6aydır uce-ct220l yi kullanıyorum ve gayet memnunum.son güncellemeden sonra daha iyi olmuş başarılarınızın devamını dilerim

  4. Juan leal inglada (verified owner)

    Finally all good, I really like constant updates, keep it up, thank you very much

Add a review

Your email address will not be published. Required fields are marked *